Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

$31.99 - $32.99 $32.99 Up to 3% Off
Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10
$585.99
Stages Gen 3 single-sided Power L meter is built onto a non-drive-side Shimano GRX RX-810 crank arm. It's compatible with all Shimano GRX Cranksets. Tour Proven Stages Power has carried riders to three consecutive Tour de France victories, plus many more world and national championships. If you believe racing provides the world's best product-proving ground, then Stages Power is proven as the world's best power meter. Active Temperature Compensation as Standard Equipment Consistency of measurement is the most important feature of a power meter. Stages Power was the first meter to make temperature compensation an automatic process, ensuring accurate readings no matter the environmental conditions. Individual meter calibration for the most accurate results. Stages Power meters are calibrated individually to ensure a +/- 1.5% accuracy level. Individual calibration means that you can trust the data produced by our system. Additional features: - +/- 1.5% accuracy in all conditions - Active temperature compensation - Accelerometer-based cadence measurement - Wirelessly upgradable firmware - LED indicator displays battery level at start up (with no need to connect to an app) and confirms successful zero reset - Updated accelerometer and addition of gyroscope for improved cadence resolution - Upgraded BLE and ANT+ radios offer a 6X improvement of data transmission strength Specifications: - Accuracy: +/- 1.5% - Power meter housing: low-profile design, with robust door interface - Weight: Only adds 15g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) when used as a single-sided meter - Power range (Watts): 0 to 5000 - Cadence range (rpm): 10-220 - Water resistance rating: IPX7 Sizing Options: - Lengths: 170mm, 172.5mm 175mm Compatibility: - This Shimano GRX RX810 Stages Power meter is compatible with all Shimano GRX cranksets. - Frame Compatibility: Most frames - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibility: Stages Link, Training Peaks, Strava, Garmin Training Center, and others
$59.99
- Shimano, FC-MT500 Crank Arm, Crank Arm, 170mm, Hollowtech II, Black, Y1VB98030
$17.00
SRAM’s cranks are strong and tough, ready for any kind of ride. So it’s inevitable that pedal strikes and debris will chip away at the end of the crank. SRAM’s Carbon Crank Boot is an upgrade that combats the wear and tear that comes with hard riding. The boot protects the crank from surface damage and keeps the rider’s style perfectly intact. - For Descendant Carbon and non-Eagle XX1 and X01
$27.00
- Replacement bolt for DUB cranks
$81.00
Replacement crank arm for GX Eagle GXP
$64.95
- Bash guard protects chainring from logs, rocks and other trail hazards - Designed and manufactured in the USA from 7075-T6 aluminum alloy - See wolftoothcycling.com for mounting tips - 51g (26-30t)
$64.95
Protect your 1x investment with this bashguard designed for Shimano Symmetrical 96 BCD cranksets. - Only compatible with symmetrical 96 BCD cranks - Made from aluminum alloy
$98.95
The Wolf Tooth CAMO BashSpider is a crankset-mounted boost bash ring. This is a spider with an integrated bash ring for use with direct mount cranksets. The CAMO BashSpider pairs with a CAMO chainring to complete the CAMO System. - A CAMO chainring is required to complete this system - The "rolling" ability of the BashSpider allows the rider to move easily over obstacles - Bash rings that are mounted on the crankset are better supported than bash rings that are mounted to the frame or bottom bracket - M5 (minus 5mm - Boost) is dished towards the frame for 52mm chainline for bikes with Boost spacing - Will fit CAMO chainrings from sizes 28T-34T round or 30T-32T elliptical - Includes mounting bolts - Designed to work with the Race Face Cinch cranksets that have a removable spider
$47.95
CAMO Spider - Made from Aluminum alloy for light weight - Includes 5 black chainring bolts
$47.95
Wolf Tooth's CAMO stands for Chainline and Material Optimization. Available in various chainlines and spider configurations, CAMO spiders allow the use of previously unavailable chainring styles, materials, and chainlines in a lightweight, modular, and customizable package. These spiders are for use with the RaceFace cranksets that have removable Cinch spiders/chainrings and are only compatible with CAMO rings and bolts. Three different chainline options are available. The number and letter refer to the mm offset and direction from the mounting face to the centerline of the teeth: - M8 (minus 8mm - dished toward the frame): For 49mm chainline, used with GXP and long-spindle BB30 cranks. Designed for bikes with 135mm QR, 142mm thru axle, and some 148mm bikes. - M5 (minus 5mm - dished toward the frame): For 52mm chainline (Boost) - P2 (plus 2mm - dished outward away from the frame): For fat bikes that have 190/197 rear spacing but use a 100mm-spindle crank
$47.95
Wolf Tooth's CAMO stands for Chainline and Material Optimization. Available in various chainlines and spider configurations, CAMO spiders allow the use of previously unavailable chainring styles, materials, and chainlines in a lightweight, modular, and customizable package. These spiders are for use with the SRAM cranksets that have removable Direct Mount spiders and are only compatible with CAMO rings and bolts. Four different chainline options are available. The number and letter refer to the mm offset and direction from the mounting face to the centerline of the teeth: - M8 (minus 8mm - dished toward the frame): For 49mm chainline, used with GXP and long-spindle BB30 cranks. Designed for bikes with 135mm QR, 142mm thru axle, and some 148mm bikes. - M5 (minus 5mm - dished toward the frame): For 52mm chainline (Boost) - M2 (minus 2mm - dished toward the frame): For 49mm chainline on short-spindle BB30 cranks - P2 (plus 2mm - dished outward away from the frame): For fat bikes that have 190/197 rear spacing but use a 100mm-spindle crank. Can also be used to achieve a Boost chainline with a short-spindle BB30 crank.
$15.99
- Some do it to protect that beautiful finish on their cranks, and some do it because they can't stand stock crankarm graphics. - Whatever your reason for wrapping and protecting a crankset, we wanted to give you an option with our branding. - These are full-wrap Crankskins that work with most cranksets One pair
$30.49
Used to adjust crank chainline or take up any slack when using 29mm (SRAM DUB) spindle cranks. - 29mm I.D. - 5mm thick - 5 spacers per bag - Machined engineering-grade Delrin
$100.49
The Wheels Manufacturing 386 EVO Adapter for 22/24mm Spindle Cranks adapts SRAM/Truvativ cranks to 386EVO-standard frames. Simply tap the adapters into the 6806 bearing in the BB shell or cups, then install the cranks using the included spacers to adjust chainline or to take up any side-to-side movement in the crank. - Machined engineering-grade Delrin - 48g/pr Includes - (1) - 24mm ID adapter (for right-side) - (1) - 22mm ID adapter (for left-side) - (8) - 0.7mm spacers
$100.49
The Wheels Manufacturing 386 EVO Adaptor for Shimano Hollowtech II Cranks adapts Shimano cranks to 386EVO-standard frames. Simply tap the adapters into the 6806 bearing in the BB shell or cups, then install the cranks using the included spacers to adjust chainline, or to take up any side-to-side movement in the crank. - Machined engineering-grade Delrin - 48g/pr Includes - (2) - 24mm ID adapters - (8 )- .7mm spacers
$95.99
Machined engineering-grade Delrin inserts for adapting bottom brackets to a different type of crankset spindle. - Adapts PF30 and Cannondale BB30-73A bottom brackets for use with SRAM/TruVativ cranksets - Delrin adaptors fit between bearings and crank spindle - BB Shell Width (mm): 68 mm , 73 mm - Spindle Interface Type: TruVativ GXP - BB/Frame Interface: PF30
$88.99
Machined engineering-grade Delrin inserts for adapting bottom brackets to a different type of crankset spindle. - Adapts PF30 and Cannondale BB30-73A bottom brackets for use with Hollowtech II cranksets - Delrin adaptors fit between bearings and crank spindle - BB Shell Width (mm): 68 mm , 73 mm - Spindle Interface Type: Hollowtech II - BB/Frame Interface: PF30
$92.99
Wheels Manufacturing BB30 Bottom Bracket Adaptor for GXP Cranks adapts 22/24mm Spindle Cranks (SRAM/TruVativ) to work on BB30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin.
$100.49
Wheels Manufacturing BB30 Bottom Bracket Adaptor for Hollowtech II Cranks adapts 24mm Spindle Cranks (Shimano Hollowtech II, FSA, Race Face EXI, etc.) to work on BB30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin.
$333.99
- 8 bikes worth of adapters for Shimano 24mm and SRAM/Truvativ 24/22mm cranks to virtually any BB30 or Pressfit 30 frame, including mountain bikes, 2x10 systems, narrow-shell road bikes, road triples, etc. - 65 piece kit includes 4 each Shimano and SRAM adapter sets, plus extra spacers for chainline adjustment and a puller for removing adapters - Includes: (8) Shimano adapter (24mm ID, Shimano right or left; SRAM right only), (4) SRAM-left adapter (22mm ID, Shimano right or left; SRAM right only), (4) SRAM-right adapter (24mm ID, Shimano right or left; SRAM right only), (12) 0.7mm spacer - right (24mm ID, Shimano right or left; SRAM right only), (4) 1.8mm spacer - right (24mm ID, Shimano right or left; SRAM right only), (4) 2.5mm spacer - right (24mm ID, Shimano right or left; SRAM right only), (8) 1.0mm spacer - left (30mm ID, SRAM), (4) 2.5mm spacer - left (30mm ID, SRAM), (4) 5mm spacer - left (30mm ID, SRAM), (4) 10mm spacer - left (30mm ID, SRAM), (8) wave washer, (1) removal tool for pulling adapter out of BB
$88.99
Wheels Manufacturing BBRIGHT BB30A and PF30A Adaptor for 24mm Spindle Cranks adapts 24mm spindle cranks (Shimano, FSA, etc.) to most BBRight frames. Compatible with 2011-2012 Cervelo models R3, R3 Team, S5, S5 Team, S5 VWD, R5ca and R5 VWD. - Also adapts Cannondale BB30a and PF30a frames to 24mm spindle cranks (Shimano, FSA, etc.). - Includes eight 0.7mm shims for fine-tuning chain line - Machined engineering-grade Delrin - 48g/pr
$88.99
The Wheels Manufacturing BBright Press Fit Bottom Bracket Adaptor for GXP Cranks adapts 24/22mm cranks (SRAM, Truvativ, etc.) to most BBRight frames. Compatible with 2011-2012 Cervelo models R3, R3 Team, S5, S5 Team, S5 VWD, R5ca and R5 VWD. - Includes eight 0.7mm shims for fine-tuning chain line - Machined engineering-grade Delrin - 8g/pr
$100.49
Wheels Manufacturing FSA PF30 Adapter for 24mm Spindle Cranks adapts 24mm Spindle Cranks (Shimano, FSA, etc.) to work on Pressfit 30 frames with FSA's PF30 bottom bracket installed. Simply tap the adapters into the 6806 bearing in the BB shell, install the spindle and cranks. Use our Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. - Machined engineering-grade Delrin - 48g/pr *NOTE: The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter
$100.49
Wheels Manufacturing Press Fit 30 Bottom Bracket Adapter for 22/24mm Spindle Cranks adapts 22/24mm Spindle Cranks (SRAM/TruVativ) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SRAM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SRAM to adapt 22/24mm Spindle Cranks (SRAM/TruVativ) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter
$92.99
The Wheels Manufacturing PressFit 30 Bottom Bracket Adaptor for Shimano Cranks adapts 24mm Spindle Cranks (Shimano Hollowtech II, FSA, Race Face EXI, etc.) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SHIM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SHIM to adapt 24mm Spindle Cranks (Shimano, FSA, etc.) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter
$31.00
- Adapts American/Pro BMX frames with a non-Threaded 51.3mm (2.02") i.d. bottom bracket shell to accept English-threaded bottom bracket & crank applications - CNC-machined aluminum with three steel connecting bolts to prevent independent rotation
$39.00
- Crank Arm Length: 175mm - Interface: ISIS - Position: Left
$17.00
TruVativ Crank Arm Fixing Bolts - Monocoque carbon crankset with hollow-arm design - FSA Mega Tooth chainring design greatly improves chain retention - FSA BB392 compatibility allows use in nearly any frame - Bottom bracket not included
$939.99
The new Gen 3 single-sided Stages Power R meter is built on to a driveside Shimano Dura-Ace R9100 crank arm and is compatible with all frames that fit Shimano Hollowtech II cranks. Tour Proven. Stages Power has carried riders to three consecutive Tour de France victories, plus many more world and national championships. If you believe racing provides the world’s best product proving ground, then Stages Power is proven as the world’s best power meter. Active Temperature Compensation as standard equipment. Consistency of measurement is the most important feature of a power meter. Stages Power was the first meter to make temperature compensation an automatic process ensuring accurate readings no matter the environmental conditions. ATC is the key reason a rider can trust data from Stages Power in all conditions. Single drive-side power meter increases frame compatibility or upgrades an existing Stages Power L meter to Stages Power LR. Stages Power R offers increased compatibility with direct mount brakes and frames that lack adequate chainstay clearance, as well as the ability to upgrade existing Stages Power L power meters to Stages Power LR bi-lateral (dual) meter systems. Additional features: - ± 1.5 % accuracy in all conditions - Active temperature compensation - Accelerometer based cadence measurement - Wirelessly upgradable firmware - LED indicator displays battery level at start up (with no need for connect to an app) and confirms successful zero reset - Updated accelerometer and addition of gyroscope for improved cadence resolution - Upgraded BLE and ANT+ radios offer a 6X improvement of data transmission strength Specifications - Power meter housing: low profile design, 2x phillips head screw to access battery compartment - Weight: Only adds 20g to base crankset - Battery Life: 175+ hours (via coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 In the box - Drive-side power meter - High quality CR2032 coin cell battery - Lifetime access to Stages Link for power meter management and firmware upgrades. - 2 months free access to Stages Link premium training and coaching features. - Product Identification Card with Serial Number and ANT+ I.D. Number. - User Guide
Page 1 of 2 Next page